Integrated Z10

LTA Integrated Amp Front.jpg
LTA Integrated Amp Side.jpg
LTA Integrated Amp Back.jpg
LTA Integrated Amp Detail.jpg
LTA Integrated Amp Front Detail.jpg
LTA Integrated Tube Amp Front.jpg
LTA Integrated Tube Amp Rear.jpg
LTA Integrated Amp Front.jpg
LTA Integrated Amp Side.jpg
LTA Integrated Amp Back.jpg
LTA Integrated Amp Detail.jpg
LTA Integrated Amp Front Detail.jpg
LTA Integrated Tube Amp Front.jpg
LTA Integrated Tube Amp Rear.jpg

Integrated Z10

4,600.00

LTA is excited to announce the first Berning Integrated Amplifier. With all the magic, realism, and 3D soundstage of ZOTL technology, the Integrated Z10 delivers the experience of a live music performance right in your living room.

Quantity:
Add To Cart

LTA is excited to announce the first Berning Integrated Amplifier. With all the magic, realism, and 3D soundstage of ZOTL technology, the Integrated Z10 delivers the experience of a live music performance right in your living room.

A single component solution, the Integrated Z10 incorporates the acclaimed ZOTL10 power amplifier, a Berning designed preamplifier, LTA’s control system, and an optional phono preamp – all beautifully packaged in a Fern & Roby designed case.

The Integrated Z10 offers all the benefits of the output transformer-less ZOTL technology with three times the tube life and one third the heat. With startling realism, plentiful bass, low noise, and gorgeous mids and highs – the Integrated Z10 is the perfect integrated package. The brass touch buttons, headphone outputs, easy-to-read, configurable display, and machined aluminum front and rear panels, exude the high quality manufacturing of handmade products in the USA..

The heart of the Integrated Z10 is the highly-acclaimed ZOTL10 power amplifier, using EL-84 power tubes at 12 watts per channel. With the addition of a preamplifier borrowed from Berning’s $30K product, the existing ZOTL circuitry cross-couples to a gain stage, and matches perfectly with the power amplifier. Exhibiting the newly updated Maverick phono preamp from Fern & Roby, complete with Berning modifications, the Integrated Z10 can power any vinyl enthusiasts turntable. The amplifier is wrapped in our new control system featuring: 5 inputs (including one true balanced input,) tape in and out, LED dimmable display with configurable time out, LED input indicators, home theater mode, remote controlled stepped attenuation using premium Vishay Dale resistors, and a linear power supply configured with a Belleson regulator for extremely low noise. Additionally, the Integrated Z10 comes equipped with two headphone output jacks: a high output for less sensitive headphones and a low output for very sensitive headphones.

Delivering much higher power than solid state amps with the same power rating, tube amplifiers can drive your 90db and above sensitivity speakers to thundering levels. Providing everything you need except speakers and a source, in a sleek new case, the Integrated Z10 is designed to last a lifetime.


SPECIFICATIONS

Inputs: 4 single-ended Cardas RCA stereo, 1 true balanced stereo input using two 3-pin XLRs

Speaker Output: 4 WBT copper speaker binding posts, banana or spade

Headphone Output: Low: Approx. 1 watt per channel, High: Approx. 2 watts per channel

Tape Monitor: 1 stereo tape monitor out, 1 stereo tape monitor in - both Cardas RCA

Front Panel Controls: 7 brass touch switches (power, input, tape monitor, up, down, menu/select, back), volume control, and headphone speaker switch

Remote Control: All front panel functions using paired Apple TV Remote (power on programmable)

Volume Control: 100 stepped attenuator (smallest step 1/1000th of total value) using Vishay Dale 1% precision resistors

Output impedance: 1.2 ohms

Input impedance: 47k

115VAC or 220VAC configured at factory - 50/60Hz - IEC receptacle

Hum and noise: 94dB below full output (measured at 20Hz-20kHz) • Carrier: -50dB (460kHz)

Power output with 4-ohm load: 12W, 0.5% THD

Power output with 8-ohm load: 10W, 0.5% THD

Frequency response (8-ohm load): 6Hz to 60kHz, +0, -.5dB

Amplifier class: Push-pull Class AB

Voltage gain (8-ohm load): 18dB

Size: 16 inches wide, 5 1/8 inches tall, 16 inches deep (including connectors)

Net weight: Amplifier: 18 lbs./8.2 kg

Finish: Aluminum case

Tube complement: two 12AT7s, four 12AU7s, and four EL-84s

Home Theater Function can select any input for fixed volume

Display: 16 Levels of brightness and programmable 7-second time out

Optional Phono Preamp: 54 dB gain for moving magnet cartridges. Moving coil cartridges supported with configurable daughter card.